View 60CTTN015_1200848.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Bulletin PD-20489 rev. A 02/03
60CTTN015
TRENCH SCHOTTKY RECTIFIER 60 Amp
Major Ratings and Characteristics Characteristics
IF(AV) Rectangular waveform PerDevice VRRM IFSM VF TJ @ tp = 5 s sine @ 30 Apk, TJ = 125C (typical) per leg range
Description/ Features Units
A V A V This center tap Schottky rectifier has been optimized for low forward voltage drop. The proprietary sub-micron technology allows for low power loss both in forward and reverse conduction. 150 C TJ operation Center tap configuration Low forward voltage drop High frequency operation High purity, high temperature epoxy encapsulation for enhanced mechanical strength and moisture resistance
Values
60 15 1800 0.3
-55 to150
C
Case Styles 60CTTN015
Base Common Cathode
2
1
Anode
2 Common Cathode
3
Anode
TO-220
www.irf.com
1
60CTTN015
Bulletin PD-20489 rev. A 02/03
Voltage Ratings
Part number
VR Max. DC Reverse Voltage (V) @ TJ = 150C
60CTTN015
15
Absolute Maximum Ratings
Parameters
IF(AV) Max. Average Forward (Per Leg) Current (Per Device) IFSM Max. Peak One Cycle Non-Repetitive Surge Current (Per Leg) EAS IAR Non-Repetitive Avalanche Energy (Per Leg) Repetitive Avalanche Current (Per Leg)
Values Units
30 60 1800 340 9.0 2 A
Conditions
50% duty cycle @ TC = 130C, rectangular wave form Following any rated 5s Sine or 3s Rect. pulse load condition and with 10ms Sine or 6ms Rect. pulse rated VRRM applied TJ = 25 C, IAS = 2 Amps, L = 4.5 mH Current decaying linearly to zero in 1 sec Frequency limited by TJ max. VA = 1.5 x VR typical
A mJ A
Electrical Specifications
Parameters
VFM Max. Forward Voltage Drop (Per Leg) (1)
Typ
0.41 0.48 0.33 0.44 0.30 0.42
Max
0.44 0.53 0.36 0.47 0.32 0.45 2 50 250 10000
Units
V V V V V V mA mA mA pF nH
Conditions
@ 30A @ 60A @ 30A @ 60A @ 30A @ 60A TJ = 25 C TJ = 100C TJ = 125 C VR = rated VR VR = 5V VR = rated VR TJ = 150C TJ = 125C TJ = 25C
IRM
Max. Reverse Leakage Current (Per Leg) (1)
0.4 31 120 3000 8.0 -
CT LS
Junction Capacitance (Per Leg) Series Inductance (Per Leg)
VR =10VDC(test signal range100KHz to1MHz) 25C Measured lead to lead 5mm from package body
dv/dt Max. Voltage Rate of Change
(1) Pulse Width < 300s, Duty Cycle < 2%
V/s (Rated VR)
Thermal-Mechanical Specifications
Parameters
TJ Tstg Max. Junction Temperature Range Max. Storage Temperature Range
Values Units
-55 to 150 -55 to 150 1.2 0.5 2 (0.07) 6 (5) 12 (10) C C C/W C/W g (oz.) Kg-cm (Ibf-in)
Conditions
RthJC Max. Thermal Resistance Junction to Case (Per Leg) RthCS Typical Thermal Resistance, Case to Heatsink wt Approximate Weight T MountingTorque Case Style Min. Max.
DC operation Mounting surface , smooth and greased
TO-220AB
2
www.irf.com
60CTTN015
Bulletin PD-20489 rev. A 02/03
1000
1000
Tj = 150C
Reverse Current - I R (mA)
125C
100
100C
10
75C 50C
Instantaneous Forward Current - I F (A)
100
1
25C
0.1 0
T = 150C J T = 125C J T = 25C J
2
4
6
8
10 12 14 16
Reverse Voltage - VR (V) Fig. 2 - Typical Values Of Reverse Current Vs. Reverse Voltage (Per Leg)
10000
T = 25C
Junction Capacitance - C T (p F)
J
10
1 0 0.4 0.8 1.2 1.6 2
Forward Voltage Drop - VFM (V) Fig. 1 - Max. Forward Voltage Drop Characteristics (Per Leg)
1000 4 6 8 10 12 14 16
Reverse Voltage - VR (V) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage (Per Leg)
10
(C/W)
thJC
Thermal Impedance Z
1
D = 0.75 D = 0.50 D = 0.33 D = 0.25 D = 0.20 Single Pulse (Thermal Resistance) Notes:
PDM
t1 t2
0.1
1. Duty factor D = t1 / t2 2. Peak Tj = Pdm x ZthJC + Tc
0.01 0.00001
0.0001
0.001
0.01
0.1
1
10
100
t1, Rectangular Pulse Duration (Seconds) Fig. 4 - Max. Thermal Impedance ZthJC Characteristics (Per Leg)
www.irf.com
3
60CTTN015
Bulletin PD-20489 rev. A 02/03
155
Allowable Case Temperature (C) Average Power Loss (Watts)
18 16 14 12 10 8 6 4 2 0 0
150 145 140 135 130
Square wave (D = 0.50) 125 80% Vr applied see note (2) 120 0 5 10 15 20 25 30 35 40 45 Average Forward Current - I F(AV) (A)
Fig. 5 - Max. Allowable Case Temperature Vs. Average Forward Current (Per Leg)
Non-Repetitive Surge Current - I FSM (A)
D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75
RMS Limit
DC
DC
5 10 15 20 25 30 35 40 45
Average Forward Current - IF(AV) (A)
Fig. 6 - Forward Power Loss Characteristics (Per Leg)
10000
At Any Rated Load Condition And With Rated Vrrm Applied Following Surge
1000
100 10
100
1000
10000
Square Wave Pulse Duration - tp (microsec) Fig. 7 - Max. Non-Repetitive Surge Current (Per Leg)
L HIGH-S PEED S CH WIT FREE-WHEEL DIODE 40HF L40S 02 Vd = 25 Volt
DUT
IR FP460 R = 25 ohm g
+
CURR ENT MONIT OR
Fig. 8 - Unclamped Inductive Test Circuit
(2) Formula used: TC = TJ - (Pd + PdREV) x RthJC ; Pd = Forward Power Loss = IF(AV) x VFM @ (IF(AV) / D) (see Fig. 6); PdREV = Inverse Power Loss = VR1 x IR (1 - D); IR @ 80% VR applied
4
www.irf.com
60CTTN015
Bulletin PD-20489 rev. A 02/03
Outline Table
10.54 (0.41) MAX. 3.78 (0.15) 3.54 (0.14) 15.24 (0.60) 14.84 (0.58) 123 14.09 (0.55) 13.47 (0.53) 3.96 (0.16) 3.55 (0.14) 2.04 (0.080) MAX. 1.40 (0.05) 1.15 (0.04) 0.94 (0.04) 0.69 (0.03) 2.89 (0.11) 2.64 (0.10)
Base Common Cathode
2
1.32 (0.05) DIA. 6.48 (0.25) 6.23 (0.24) 2 1.22 (0.05)
2.92 (0.11) 2.54 (0.10) TERM 2
0.10 (0.004)
123 4.57 (0.18) 4.32 (0.17)
0.61 (0.02) MAX.
5.08 (0.20) REF.
1
Anode
2 Common Cathode
3
Anode
Conform to JEDEC outline TO-220AB Dimensions in millimeters and (inches)
Data and specifications subject to change without notice. This product has been designed for Industrial Level. Qualification Standards can be found on IR's Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 02/03
www.irf.com
5

▲Up To Search▲

Price & Availability of 60CTTN015

	To Download 60CTTN015 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .